Search Results - M109Riders.com

Search:

Type: Posts; User: TRod

Page 1 of 17 1 2 3 4

Search: Search took 0.26 seconds.

  1. Replies
    34
    Views
    1,030

    I thought maybe I would try and lighten things up...

    I thought maybe I would try and lighten things up a bit. But, clearly that's not how it came across to you. So, with that, it is goodbye. I am now done with M109 riders. I suppose many, including...
  2. Replies
    34
    Views
    1,030

    Hmmmmm. Just thinking out loud here. But I recall...

    Hmmmmm. Just thinking out loud here. But I recall this very thing being listed in the service manual as a symptom of valve clearance being out. Have you checked the valve clearance yet? Because, if...
  3. Thread: fault code po352

    by TRod
    Replies
    7
    Views
    378

    If you swapped coils and the problem stayed the...

    If you swapped coils and the problem stayed the same then it might be in the wiring going to the bad coil. You might have to look at the wiring diagram and do some metering of the wires that feed...
  4. Thread: Speedometer help

    by TRod
    Replies
    11
    Views
    365

    Orange green trace comes off the signal fuse at...

    Orange green trace comes off the signal fuse at the fuseblock. But, it powers the horn and the speedo as well.
  5. 24,000 Kms or 2 years according to the manual...

    24,000 Kms or 2 years according to the manual which you seem rather fond of. I know for sure one of those has requirements has long passed for both yours and your hubby's bikes.

    Better not ride...
  6. If you think it's do damn easy go do yours and...

    If you think it's do damn easy go do yours and your hubby's both and come tell how easy it was.
  7. Even a broken clock is right twice a day.

    Even a broken clock is right twice a day.
  8. So you boys think you got me pegged. Eh? Well, I...

    So you boys think you got me pegged. Eh? Well, I might surprise you on this one.

    At 73K, and having exhausted all the easy stuff (fuel, plugs, filter etc), then it might be time to check the valve...
  9. Replies
    715
    Views
    52,785

    Got it. :bigthumbsup:

    Got it. :bigthumbsup:
  10. Thread: Coolant leak

    by TRod
    Replies
    71
    Views
    15,659

    There is an o-ring on that fitting where it fits...

    There is an o-ring on that fitting where it fits into the cylinder. Have seen that leak before.
  11. Replies
    12
    Views
    643

    Some people don't even know why #13 is there and...

    Some people don't even know why #13 is there and they don't put it back. It's there because that bolt intersects an oil passage.
  12. Replies
    12
    Views
    643

    Well, then, that would be the left or stator side.

    Well, then, that would be the left or stator side.
  13. Replies
    2
    Views
    241

    47432-48G00 $15 ...

    47432-48G00

    $15

    http://www.oneidasuzuki.com/store/parts-accessories/tool-kit-holder-m109-2006-08.html
  14. Replies
    12
    Views
    643

    Maybe it would have been easiest to say right...

    Maybe it would have been easiest to say right side. You really don't need to drain the oil if you have it on the sidestand. You won't lose but a few drops of oil when you take the cover off.
  15. Replies
    6
    Views
    2,013

    The return spring(s) is on the throttle body(s)....

    The return spring(s) is on the throttle body(s). It would be difficult to change it to a lighter spring(s).

    Use a throttle rocker. It makes a huge difference.
  16. Replies
    4
    Views
    297

    According to the manual a GL-5 rated is...

    According to the manual a GL-5 rated is recommended.
  17. Replies
    12
    Views
    643

    He says behind the derby cover which is the left...

    He says behind the derby cover which is the left side. He also refers to the driveshaft, also on the left.

    I think he means stator side.
  18. Replies
    16
    Views
    574

    While both of you make a good point of pointing...

    While both of you make a good point of pointing out that not all o-rings are equal, no matter how good the o-ring that seals the gas tank on the M109R is it doesn't justify the price they charge....
  19. Replies
    12
    Views
    709

    There are numerous ways to accomplish it. I chose...

    There are numerous ways to accomplish it. I chose this route. I brought a single wire from the batt (fused) and a ground to a pair of terminal blocks.
    ...
  20. Replies
    16
    Views
    574

    Now that looks more like your speed. Less chance...

    Now that looks more like your speed. Less chance of you getting hurt on that.
  21. Thread: Help!

    by TRod
    Replies
    7
    Views
    346

    Pretty sure I agree with the others on this one....

    Pretty sure I agree with the others on this one. It's not an adjustment issue, it's the 2nd gear issue that some bikes suffer. Lots of work and $ to fix.
  22. Replies
    97
    Views
    2,875

    Huh, I guess then I'm not worthy. Your dream...

    Huh, I guess then I'm not worthy. Your dream holiday includes Rick but not me.
  23. Replies
    7
    Views
    461

    The Cobra does not need to be reset nor is there...

    The Cobra does not need to be reset nor is there anything to running through the gears with it upon install.

    However, the earlier units did not have the single pot to adjust for steady state...
  24. Thread: 300 swingarm

    by TRod
    Replies
    45
    Views
    1,551

    Did you also make a spacer for the bearing spacer?

    Did you also make a spacer for the bearing spacer?
  25. Thread: 300 swingarm

    by TRod
    Replies
    45
    Views
    1,551

    If you stand back and look at a stock M109, the...

    If you stand back and look at a stock M109, the rear tire is already offset.
  26. Thread: 300 swingarm

    by TRod
    Replies
    45
    Views
    1,551

    Well, you selfish POS, how does that help anyone...

    Well, you selfish POS, how does that help anyone else?
  27. Replies
    5
    Views
    364

    PM sent

    PM sent
  28. Thread: 300 swingarm

    by TRod
    Replies
    45
    Views
    1,551

    If all this is true, someone needs to be to...

    If all this is true, someone needs to be to talking to the wheel manufacturers about how they make the wheel. This issue could easily be solved by simply machining the wheel with the needed 1/4"...
  29. Replies
    24
    Views
    970

    I guess I would have come up with a different...

    I guess I would have come up with a different solution. Don't put in 3.8 quarts.

    If your bike is lowered, then it may not drain the full 3.8 quarts which is what Suzuki says a stock bike will...
  30. Replies
    24
    Views
    970

    That's kinda the way I see it. When 25% of the...

    That's kinda the way I see it. When 25% of the oil is going to be old, used oil, what does a few ounces matter either way.
Results 1 to 30 of 500
Page 1 of 17 1 2 3 4