Search Results - M109Riders.com

Search:

Type: Posts; User: kellyd67

Search: Search took 0.01 seconds.

  1. I read through that post on Facebook and laughed...

    I read through that post on Facebook and laughed hysterically when he lost it over the truth. Bcs do a good job of not making look like a total idiot. I wouldn't have been so nice. Lol
  2. Replies
    22
    Views
    853

    There's a shop near me thar is always doing...

    There's a shop near me thar is always doing promotions. Bike nights, cookouts, anything to generate traffic. There also a large dealership. Mcgrath powersports in cedar rapids iowa. It's a long way...
  3. Replies
    5
    Views
    318

    Mine acted similar . And pulled hard, lubed cable...

    Mine acted similar . And pulled hard, lubed cable and problem solved
  4. Replies
    0
    Views
    147

    Ultimate seat drivers backrest

    Just wondering if anyone has s drivers backrest for an ultimate seat that they would like to sell
    Thanks
  5. Replies
    65
    Views
    2,890

    Thanks

    Thanks
  6. Replies
    65
    Views
    2,890

    Thank you

    Thank you
  7. Replies
    65
    Views
    2,890

    Looking for wiring for rear lights and connector...

    Looking for wiring for rear lights and connector for the main harness so i can build a plug and play trailer harness let me know if you have a harness thank you
  8. Replies
    6
    Views
    524

    Set handle adjustment all the way in . Adjust...

    Set handle adjustment all the way in . Adjust lower until there's 10 to 15 mm play at the ball end of handle . Small adjustments can be made at handle after that
  9. Replies
    7
    Views
    476

    I have the rifle solo and lowers. I like its...

    I have the rifle solo and lowers. I like its adjustability. Isn't the coolest windsh5to look at but it's nice on a 300 mi day
  10. Thread: Clutch lever

    by kellyd67
    Replies
    5
    Views
    283

    I think +2 . I will check that out thanks ....

    I think +2 . I will check that out thanks . Didn't know stock cable would work
  11. Thread: Clutch lever

    by kellyd67
    Replies
    5
    Views
    283

    I believe its a motion pro. Previous owner...

    I believe its a motion pro. Previous owner installed because of longer risers
  12. Thread: Clutch lever

    by kellyd67
    Replies
    5
    Views
    283

    Clutch lever

    Has anyone tried to bend clutch lever to increase pull. If i adjust it to not slip can't get into neutral. If i adjust it to go to neutral easily slips intermittently under full throttle. And a revo...
  13. Replies
    184
    Views
    6,597

    Removed pcv, installed big air kits, changed...

    Removed pcv, installed big air kits, changed plugs and put tuned ecu back in. Thanks to bcs performance. It runs fantastic
  14. Replies
    184
    Views
    6,597

    I have them on mine as highway pegs they're...

    I have them on mine as highway pegs they're mediocre at best. They comfortable folded. I am going to drill another hole halfway out for the wings to lock into
  15. Replies
    25
    Views
    1,089

    Mine were crooked and moved up and down 3 inches....

    Mine were crooked and moved up and down 3 inches. Put 1/2 aluminum block cut to match risers and added 3 degrees of angle on the block. Raised bars up off the tank almost 3 1/2 inches. Bars stay...
  16. Thread: Swing saddle

    by kellyd67
    Replies
    8
    Views
    547

    I was thinking the same thing . I am making it...

    I was thinking the same thing . I am making it out of some 1/8 in. Stock i had laying around. And slightly longer bolts so peg can be used.
  17. Replies
    3
    Views
    521

    I have them on my 109 installed by previous owner...

    I have them on my 109 installed by previous owner with the parts that came with it . Now the servo sticks and ligjt comes on. I will be lnstalling servo elminator
  18. Replies
    8
    Views
    289

    Welcome from the middle of iowa

    Welcome from the middle of iowa
  19. Thread: Clutch slave

    by kellyd67
    Replies
    12
    Views
    498

    Very interesting read. Thanks

    "Hunter" a member here described the stiffness of hydr. clutch in his installation :

    https://issuu.com/hunter_guyv2/docs/hydraulic_clutch_install_step_by_step_english[/QUOTE]
    Very interesting...
  20. Thread: Clutch slave

    by kellyd67
    Replies
    12
    Views
    498

    To make the pull easier and not have to worry...

    To make the pull easier and not have to worry about cable breaking
  21. Thread: Clutch slave

    by kellyd67
    Replies
    12
    Views
    498

    I've looked at these but don't know if will work....

    I've looked at these but don't know if will work. This would be a nice option though
  22. Thread: Clutch slave

    by kellyd67
    Replies
    12
    Views
    498

    Clutch slave

    Does anyone know of a clutch slave other than the revo kit
    Thanks
Results 1 to 22 of 23