Search Results - M109Riders.com

Search:

Type: Posts; User: HEADVINCE

Page 1 of 3 1 2 3

Search: Search took 0.03 seconds.

  1. Replies
    119
    Views
    6,105

    Re: Just put the JSD 3-M kit on

    DITTO I HAVE HAD MINE ON FOR 3 WEEKS NOW AND IT IDLES AT 1200 IN NEUTRAL. THE REASON I GOT THE 3M WAS TO KEEP IDLE AT 900 OTHERWISE I WOULD HAVE STUCK WITH THE 1M (WHICH I ALREADY HAD ON) AND SAVE...
  2. Re: SILVER WITH NEW TURN SIGNALS,MIRRORS AND PIPES

    Good quality and good coating better feel as you would expect.
  3. Re: SILVER WITH NEW TURN SIGNALS,MIRRORS AND PIPES

    I put these brake lines on last Tuesday. If you hit any snags let me know. I still have to do the rear. look forward to the pictures I never get tired of looking at these bikes....
  4. Re: SILVER WITH NEW TURN SIGNALS,MIRRORS AND PIPES

    here is a link if you have not seen it yet.

    https://www.m109riders.com/forum/index.php?topic=935.0
  5. Replies
    19
    Views
    3,056

    Re: OK HERE ARE PICS OF THE NITROUS SILVER

    Somebody has been BUSY!! Looks Good :bigthumbsup:
  6. Replies
    18
    Views
    2,829

    Re: Tamed my Cobras a bit

    the baffles improve low end, which they do. They may drop top hp but torque will go up. the sound is deep, it does not seem as loud as with baffles out but tone is as deep. I am going to dyno...
  7. Replies
    18
    Views
    2,829

    Re: Tamed my Cobras a bit

    I put a set of these baffles in mine. the pitch seems deeper. they favor your washer, but the baffle is alot shorter.

    http://www.bigcitythunder.com
  8. Re: SILVER WITH NEW TURN SIGNALS AND MIRRORS

    about 20lbs with exhaust and another 10lbs for everthing else. This is a link for tach.


    https://www.m109riders.com/forum/index.php?topic=484.0
  9. Re: SILVER WITH NEW TURN SIGNALS,MIRRORS AND PIPES

    THE FRONT TURN SIGNALS ARE THE BULLETS FROM K├╝ryakyn AND I DRILLED OUT THE MOUNT THAT HELD THOSE TWO CHROME DUMBELLS ON THE FRONT THAT THE ORIGINAL TURN INDICATORS WERE ATTACHED TOO.
  10. Re: Rear Plate Bracket Installation Difficulties

    This is some tough metal. I clamped it to a board (2/6) and then clamped some scrape angle iron I had at the crease I wanted to bend. Then I had a 2/4 and pushed on the other part of the plate. Hope...
  11. Re: Rear Plate Bracket Installation Difficulties

    I had the same problem with my bracket, so I reversed it. I had to bend it but it fits nice now and fits under fender a little more.
  12. Re: SILVER WITH NEW TURN SIGNALS,MIRRORS AND PIPES

    The headlight has the two bolts and two push button fastners at the the top on the left and right. Same kind that hold the side covers on under the seat.
  13. Re: SILVER WITH NEW TURN SIGNALS AND MIRRORS

    they sell some extensions that might work, you might have to make a dimple in it so the set screw will work or tap it. When you take them off you can see how they fit. You will still have to take the...
  14. Re: Silver Bikes - Reply only if you own a silver bullet.

    :bigthumbsup:
  15. Replies
    20
    Views
    1,633

    Re: FI control modules

    the TEKA can go -100 to +100 in idle and throttle positions 10%,25,50,and 100%. it is equivalent to 4 or 5 mains.
  16. Replies
    6
    Views
    1,078

    Re: Removing top speed limiter...HELP

    it is red- violet- red -gold for 2.7 k ohm

    try this link┬* ┬* ┬*

    ┬* ┬*...
  17. Replies
    15
    Views
    1,695

    Re: Attention Dragster Owners!

    only when you whack the throttle, so that means all the time for me :D
  18. Replies
    15
    Views
    1,695

    Re: Attention Dragster Owners!

    THANKS I WILL TRY IT :bigthumbsup:
  19. Replies
    26
    Views
    1,552

    Re: Fuel Injection Pump Squeeks ...

    I AM SURE SUZUKI WILL PUT OUT A TSB SINCE IT MAY CAUSE A WARRANTY ISSUE WITH THE ACTUATOR. THAT WAY THE SERVICE TECHS CAN ADDRESS THE ISSUE BEFORE SUZUKI HAS TO REPLACE SOMETHING ON THE BIKE.
  20. Replies
    26
    Views
    1,552

    Re: Fuel Injection Pump Squeeks ...

    You may want to try some high temp grease or hig temp nickle anti-seize around the spring of the valve.
  21. Replies
    26
    Views
    1,552

    Re: Fuel Injection Pump Squeeks ...

    sorry my eyes are not as good as they used to be I forget and leave it on.

    Man that means my memory is going too. :D
  22. Replies
    26
    Views
    1,552

    Re: Fuel Injection Pump Squeeks ...

    MINE DID IT BEFORE I PUT ON NEW PIPES. AFTER 100 MILES IT STRIPPED THE SOLENOID AND HAD TO BE REPLACED. THAT VALVE GETS SUPER HOT. BE CAREFUL WITH THE CABLES AND DO NOT PULL ON THEM THE INSIDE OF...
  23. Replies
    4
    Views
    930

    Re: Air / Fuel Ratio

    THANKS FOR THE READ. :bigthumbsup:
  24. Replies
    45
    Views
    4,996

    Re: Turn it up fellows!

    MAN I KNEW I HEARD A LOUD SOUND COMING FROM THE NORTHWEST :bigthumbsup:

    I FORGOT THEY DO LOOK GOOD ON BLACK :D
  25. Thread: Oil Filter

    by HEADVINCE
    Replies
    14
    Views
    1,506

    Re: Oil Filter

    This is pretty good read on filters if you guys have not seen it before.

    http://www.tobycreek.org/oil_filters/index.shtml
  26. Replies
    8
    Views
    712

    Re: Worth the wait

    Have fun ,I know you will :bigthumbsup:
  27. Replies
    1
    Views
    727

    Re: Chrome to Black Headlight Fairing

    part #1 is chrome, part #2 is the colored part , black,silver, or blue.

    it would have been cool though.
  28. Thread: new member

    by HEADVINCE
    Replies
    2
    Views
    770

    Re: new member

    welcome, if you do a search i know somebody fixed a noise under his tank.

    good luck.

    this is it https://www.m109riders.com/forum/index.php?topic=136.0
  29. Replies
    4
    Views
    683

    Re: I thought someone was messing with me.

    not yet , the closest one is 120 miles away or if they bring one in for a special event. Just from my seat of the pants I set everything back to stock and kept my 10% setting at 10%. I will adust the...
  30. Replies
    4
    Views
    683

    Re: I thought someone was messing with me.

    thats all that new high tech packing material.

    Lamonster, I also weighed my stock pipe(minus solenoid) last night 45.7 lbs if my scales are right.

    I know there is not that much weight in the...
Results 1 to 30 of 74
Page 1 of 3 1 2 3